Sustainability Guides for Polyester Knits
Polyester is a petroleum-based fibre, and its sustainability is therefore assessed through specific levers. These are chemical safety, recycled content with a documented chain of custody, water and energy in the dyehouse, microfibre shedding and product lifetime. The five guides in this category explain how each lever is measured, which standard verifies it and how a supplier claim is read.
This category brings together the questions that a buyer, a product developer and an engineer face when a sustainability claim is made for a polyester knit. A claim only carries weight together with what it measures and how. A carbon figure depends on the system boundary and the functional unit, a recycled-content statement on its chain-of-custody certificate, and a shedding result on the test method. The guides therefore always state the standard, the boundary or the test condition next to the number.
The five guides follow the order in which a sourcing decision is usually built. Start with the overview of the levers and the life-cycle assessment, then read which question each label answers. The recycling guide explains the difference between mechanical and chemical rPET, and the microplastics guide covers how shedding is measured and reduced. The last guide sets out the data that the Digital Product Passport will require.
Decisions made in this category
| Decision | What to check |
|---|---|
| Which sustainability levers apply to a polyester knit? | Chemical safety (OEKO-TEX STANDARD 100), recycled content, dyehouse water and energy, and product lifetime; GOTS and organic certifications do not apply to polyester Sustainability in Polyester Knits: Safety, Recycling, Durability |
| Can two carbon footprint figures be compared? | The same system boundary (cradle-to-gate or cradle-to-grave), the same functional unit and the same impact method, preferably in a third-party-verified LCA Sustainability in Polyester Knits: Safety, Recycling, Durability |
| Which label answers which question? | GRS and RCS for recycled content, OEKO-TEX STANDARD 100 for harmful substances in the finished product, STeP for the facility, bluesign and the ZDHC MRSL for chemical input The Standards Map: GRS, RCS, OEKO-TEX, bluesign, ZDHC |
| How much weight does a recycled-content claim carry? | The standard (GRS or RCS), the recycled percentage and the chain-of-custody model (physical segregation or mass balance) The Standards Map: GRS, RCS, OEKO-TEX, bluesign, ZDHC |
| Which recycled polyester is being offered? | The route (mechanical or chemical), the intrinsic viscosity in dL/g measured to ASTM D4603 / ISO 1628-5, and the chain-of-custody certificate Polyester Recycling: Mechanical and Chemical Routes |
| How is the microfibre shedding of two fabrics compared? | Mass loss per kg of fabric measured to ISO 4484-1 or the TMC method under the same laboratory conditions; filament or staple yarn, twist and raising finishes explain the difference Microplastics: Fibre Shedding and Control |
| Which data will a Digital Product Passport ask for? | Fibre composition and recycled share, SVHC declaration, durability and care information, traceability of production steps and certification references; delegated acts under ESPR set the exact fields Digital Product Passport (DPP) & ESPR: What It Means for Textiles |
Key facts
- Virgin polyester’s cradle-to-gate global warming potential is reported across a wide band of roughly 2.2 to 5.5 kg CO2e/kg. Mechanically recycled rPET typically shows a 30–70% lower GWP. Sustainability in Polyester Knits: Safety, Recycling, Durability
- For dope dyeing, published LCAs report ~50–80 L of water saved per kg and a ~30–50% energy/CO2 reduction at the coloration stage. The gain belongs only to the dyeing step. Sustainability in Polyester Knits: Safety, Recycling, Durability
- In one study rPET fleece showed higher initial shedding than virgin PET fleece (~485 vs ~295 mg/kg), so low-carbon and low-shedding claims must be measured and verified separately. Sustainability in Polyester Knits: Safety, Recycling, Durability
- RCS applies from a minimum of 5% recycled content. GRS requires at least 20% for business-to-business use and at least 50% for a consumer-facing label. The Standards Map: GRS, RCS, OEKO-TEX, bluesign, ZDHC
- Under OEKO-TEX STANDARD 100 the typical limit for free/partially releasable formaldehyde is ≤20 mg/kg in Class I (babies and children under 3) and roughly ≤75 mg/kg in Class II (direct skin contact). The Standards Map: GRS, RCS, OEKO-TEX, bluesign, ZDHC
- In the mechanical route intrinsic viscosity typically drops from ~0.80 dL/g bottle-grade input to ~0.65 dL/g after processing. Solid-state polycondensation (SSP) can lift it back to ~0.7–0.9 dL/g. Polyester Recycling: Mechanical and Chemical Routes
- Independent measurements report that end-of-machine filters reduce wash-water emission by ~78% (XFiltra) and ~80% by weight (Lint LUV-R). A filter complements a low-shedding fabric design and does not replace it. Microplastics: Fibre Shedding and Control
- ESPR (Regulation (EU) 2024/1781) entered into force in July 2024. Textiles are among its priority product groups, and delegated acts set the exact DPP data fields and timeline. Digital Product Passport (DPP) & ESPR: What It Means for Textiles
Reading order
- Sustainability in Polyester Knits: Safety, Recycling, Durability — Polyester is petroleum-based, so the sustainability argument has to be framed correctly: the real levers are chemical safety (OEKO-TEX STANDARD 100), recycled content (GRS/RCS chain of custody), water and energy in the dyehouse, and product lifetime. Microfibre shedding is measured to ISO 4484-1:2023 and AATCC TM212; durability is itself a sustainability lever.
- The Standards Map: GRS, RCS, OEKO-TEX, bluesign, ZDHC — Every sustainability label answers a different question; you cannot read a claim until you know what each one actually certifies. GRS/RCS certify content, OEKO-TEX STANDARD 100 product safety, and ZDHC and bluesign the chemical input.
- Polyester Recycling: Mechanical and Chemical Routes — Mechanical recycling shortens the chain and carries colour through; chemical depolymerization breaks the polymer back to monomer and rebuilds virgin-equivalent quality — the difference lives in whether intrinsic viscosity is preserved. The single number separating the two routes is intrinsic viscosity (ASTM D4603 · ISO 1628-5).
- Microplastics: Fibre Shedding and Control — The micro-fibres that break off fabric during washing and wear are cited as the single largest source of primary microplastics in the ocean — yet shedding is measurable and can be engineered down through fibre choice and construction. Shedding is measured to ISO 4484-1 (laboratory), -2 and -3.
- Digital Product Passport (DPP) & ESPR: What It Means for Textiles — The EU’s ESPR regulation and the Digital Product Passport (DPP) change what a fabric buyer will ask a supplier for: scope, timeline, data fields, and why a vertically integrated mill is structurally ready.