Finishing and Performance Guides for Polyester Knits
Finishing decides what a greige polyester knit does in use. Chemical finishes add wicking, water repellency, UV protection, antistatic or antibacterial performance, while brushing raises the surface to enlarge the air layer. These four guides explain how each effect works, which standard measures it and how many washes it has to survive.
This category brings together the treatments applied after knitting and the tests that prove their effect. A finish is chosen for its end use but accepted on a measured value, such as a moisture-management grade under AATCC 195, a spray-test rating under ISO 4920 / AATCC TM22, or a weight band and nap for warm knits. For chemical finishes, that value carries commercial meaning only if it holds after laundering. The guides therefore state the standard and the wash conditions next to every number.
The four guides move from the general to the specific. Start with the overview of functional finishes and how to choose between them. Then read how moisture management is measured and kept after washing, how PFAS-free water repellency works and where its limit lies, and finally where warmth comes from in brushed, unbrushed and fleece structures.
Decisions made in this category
| Decision | What to check |
|---|---|
| Which functional finish does the end use need? | Antibacterial for sportswear, underwear and socks, UV for beach, outdoor and children’s wear, water-repellent for light rain and splash, antistatic for dry environments Functional Finishes for Polyester Knits |
| Can wicking and water repellency go on the same fabric? | Compatibility of the finish combination, its effect on hand and breathability, and OEKO-TEX certification for skin-contact goods Functional Finishes for Polyester Knits |
| How is moisture management proven? | Vertical wicking to AATCC 197, one-way transport (R) and OMMC to AATCC 195 (MMT), and drying rate to AATCC 201 Moisture-Wicking Finishing in Polyester Knits |
| Will the wicking claim still hold after washing? | MMT and wicking grades after a defined wash count to ISO 6330, and whether the finish adheres physically or bonds covalently to the fibre Moisture-Wicking Finishing in Polyester Knits |
| Is a PFAS-free DWR enough for the product? | Whether oil repellency is critical, since PFAS-free finishes repel water but score low on the AATCC TM118 oil scale (0–8) Durable Water Repellency (DWR): PFAS-Free Chemistry and Durability |
| Should the fabric be water-repellent or waterproof? | Spray-test rating to ISO 4920 / AATCC TM22 for repellency, hydrostatic head to ISO 811 for waterproofness Durable Water Repellency (DWR): PFAS-Free Chemistry and Durability |
| Brushed or unbrushed back for a warm knit? | The balance between brushing, which gives a warmer surface at the same weight, and an unbrushed back, which pills less and looks cleaner inside Brushed, Unbrushed and Fleece: Where Warmth Comes From in Polyester Knits |
Key facts
- An unfinished polyester filament typically shows a water contact angle of ~70–80°. A durable hydrophilic finish pushes that angle to near zero in practice, and on a well-finished fabric the drop disappears within seconds. Moisture-Wicking Finishing in Polyester Knits
- In the AATCC 195 (MMT) test, OMMC ≥ 0.8 corresponds to the excellent moisture management class. For one-way transport capacity (R), a value typically above ~400 is the highest grade. Moisture-Wicking Finishing in Polyester Knits
- AATCC 201 measures drying rate on a heated plate set to 37°C. The method delivers 0.2 mL of water to the centre of the specimen and tracks the evaporation rate, typically in g/h, under horizontal airflow. Moisture-Wicking Finishing in Polyester Knits
- For a hydrophilic finish, the acceptance criterion is typically that MMT and wicking values lose no grade after a defined wash count, for example 20–50 domestic washes per an ISO 6330 procedure. Moisture-Wicking Finishing in Polyester Knits
- In the spray test (AATCC TM22 / ISO 4920), 250 mL of distilled water is discharged over roughly 25–30 seconds onto fabric tensioned on a 150 mm hoop tilted at 45°. AATCC scores of 100, 90 and 80 correspond to ISO grades 5, 4 and 3. Durable Water Repellency (DWR): PFAS-Free Chemistry and Durability
- Water has a surface tension of ~72 mN/m and common oils only 18–33 mN/m. Close-packed -CF3 groups reach ~6 mN/m, whereas -CH3 groups bottom out at 22–24 mN/m. Oil repellency is therefore in practice a zone reachable only with fluorine. Durable Water Repellency (DWR): PFAS-Free Chemistry and Durability
- Depending on the resin, DWR curing typically sits in the ~150–170°C band. A good PFAS-free silicone finish can hold its full score (ISO-5) on polyester after 5 washes of the ISO 105-C10 type. Durable Water Repellency (DWR): PFAS-Free Chemistry and Durability
- Brushed three-thread fleece typically runs at 250–350 g/m² and gives the highest warmth of the structures compared. Brushing does not change the weight but gives a warmer surface at the same weight. Brushed, Unbrushed and Fleece: Where Warmth Comes From in Polyester Knits
Reading order
- Functional Finishes for Polyester Knits — A finish is the treatment that changes what a greige knit does, and each rests on different physics: water repellency lowers surface energy, antistatic conducts charge away, UV finishes absorb light, antimicrobial chemistry breaks the bacterial chain. The decisive question is not what the finish does but how many washes it survives; for skin-contact goods, chemical safety is evidenced by OEKO-TEX.
- Moisture-Wicking Finishing in Polyester Knits — Wicking is not polyester absorbing moisture but transporting it through capillary channels between filaments — the fibre stays hydrophobic; structure and finish do the moving. Vertical wicking is measured to AATCC 197, the real engineering depth to AATCC 195 (MMT), and drying rate to AATCC 201. What matters is that these values survive ISO 6330 laundering without losing a grade.
- Durable Water Repellency (DWR): PFAS-Free Chemistry and Durability — Water repellency is a surface-energy game PFAS-free chemistry can win — but oil repellency is still fluorine’s territory. Performance is measured by the ISO 4920 / AATCC TM22 spray test; durability is that same test repeated after laundering.
- Brushed, Unbrushed and Fleece: Where Warmth Comes From in Polyester Knits — Warmth in a knit comes from two places: trapped air and surface pile. French terry holds air with its looped back (150–350 g/m²), three-thread fleece builds a heavier base (200–350 g/m²), and brushed fleece raises the surface to enlarge the air layer (100–400 g/m²). Brushing does not change the weight; it gives a warmer surface at the same weight.
Frequently asked questions
Can polar fleece be brushed on one side only?
Yes. Polar is a separate family in which the yarn is knitted and then one or both faces are fully napped. Brushing does not change the weight, it gives a warmer surface at the same weight. One-sided or two-sided brushing and the weight are stated in the order specification.
How do I choose a quick-drying fabric that does not hold water?
The polyester fibre is hydrophobic and does not absorb moisture. Quick drying comes from structure and finish, with moisture transported through capillary channels between the filaments. Vertical wicking is measured to AATCC 197, moisture management to AATCC 195 and drying rate to AATCC 201.