Category guide · 01

Yarn and Fibre Guides for Polyester Knits

A polyester knit takes its character from fibre and yarn before knitting begins. Moisture regain decides how fast the fabric dries, and the glass transition sets the threshold at which dye enters the fibre. Filament fineness, texturing and the blend set hand and stretch. These six guides explain each layer and how to write it into an enquiry.

This category brings together the fibre and yarn decisions made before knitting. “Polyester fabric” names a fibre, not a fabric construction, and the same fibre yields very different fabrics depending on yarn form and processing. A buyer chooses the filament fineness, whether the yarn is textured, which second fibre goes into the blend and whether the raw material is virgin or recycled. Each of these choices can be written as a measurable value. The guides therefore state the number together with its unit and test method.

The six guides run from the fibre to the order. Start with the measurable constants of polyester fabric, then read how filament fineness and the melt-spinning line shape a yarn, and how texturing turns flat filament into DTY. Blends and recycled polyester follow. The last guide matches the trade names of the fabrics to their structures, so that an order is defined by structure, weight and yarn.

Decisions made in this category

DecisionWhat to check
What does an enquiry for polyester fabric need to state?Construction (woven or knitted, and which knit), weight window in g/m², composition and elastane share, expected finish and certification
What Is Polyester Fabric? The Full Spec Sheet, From a Mill
Which filament fineness gives the target hand?Denier per filament (dpf = total denier ÷ filament count); below ~1 dpf the yarn enters microfibre territory
Polyester Knit Basics: The Backbone of Performance
Should the fabric use FDY or DTY?Flat, lustrous, low-bulk FDY for satin-like glossy surfaces and lining fabrics; crimped DTY for bulk, opacity, stretch and moisture transport
DTY Textured Yarn: Bulk, Stretch and Wicking
What should be asked of a DTY supplier?Set or non-set, the target crimp contraction (CC%) band and nips/m, instead of the surface-level description “DTY 150/48”
DTY Textured Yarn: Bulk, Stretch and Wicking
Which blend suits the product?Cotton or modal for softness, elastane for stretch and recovery, a high polyester share for durability; for sport, polyester stays dominant
Polyester Blends: Cotton, Elastane, Modal
How is a recycled polyester (rPET) claim verified?The material’s technical identity (IV, b*, acetaldehyde, moisture, contaminant level) together with proof of content (GRS/RCS certificate and transaction certificates)
Recycled Polyester (rPET) in Knits
Is the trade name enough for an order?Structure, weight and yarn together; süprem, single jersey and polyester jersey are one fabric, and double-face interlock is known as ponte
Naming in Polyester Knits: When One Fabric Has Many Names

Key facts

  • Polyester has a commercial moisture regain of 0.4%, against 8.5% for cotton and 16.5% for wool. Because the fibre holds almost no water it dries quickly, and moving sweat to the surface is the job of construction and finish. What Is Polyester Fabric? The Full Spec Sheet, From a Mill
  • The glass transition of polyester sits at ~70–80 °C dry and ~65 °C in water, the threshold at which dye can enter the fibre. Disperse dyeing runs at ~130 °C (HT/HP) in a pressurised vessel. What Is Polyester Fabric? The Full Spec Sheet, From a Mill
  • The melting temperature of ~255–260 °C is the ceiling for heat-setting and ironing. The iron typically stays on the 110 °C setting with a press cloth, and a gentle wash at 30–40 °C does not disturb the fibre. What Is Polyester Fabric? The Full Spec Sheet, From a Mill
  • The same 150-denier yarn gives ≈3.1 dpf at 48 filaments and ≈1.0 dpf at 144. The weight is identical, but the two fabrics are completely different, and below ~1 dpf the yarn enters microfibre territory. Polyester Knit Basics: The Backbone of Performance
  • Apparel POY/FDY typically sits around ~0.62–0.68 dL/g intrinsic viscosity, while bottle and technical (high-tenacity) grades run markedly higher at ~0.70–0.85+ dL/g. The value is measured to ASTM D4603. Polyester Knit Basics: The Backbone of Performance
  • In DTY a first heater at ~200–220 °C gives flat POY filament a permanent crimp by false twist, and a second heater (yarn exit ~130–180 °C) kills residual torque. Crimp contraction is measured to ISO 5688. DTY Textured Yarn: Bulk, Stretch and Wicking
  • Typically 3–10% elastane is added to a polyester/elastane knit, and this small share gives clear stretch and recovery. Elastane is sensitive to heat and chlorine, so heat-setting and finishing parameters are tuned accordingly. Polyester Blends: Cotton, Elastane, Modal
  • RCS tracks a recycled-content claim from a minimum of 5% recycled input. GRS sets a higher threshold (minimum 50%) and also covers social, environmental and chemical requirements. Recycled Polyester (rPET) in Knits

Reading order

  1. What Is Polyester Fabric? The Full Spec Sheet, From a Mill — Polyester fabric is a synthetic cloth woven or knitted from filament or staple drawn out of PET polymer. This guide defines it by its measurable constants rather than by adjectives: melting and glass-transition temperature, moisture regain, filament fineness, the dyeing threshold and the weight band. Every number here is a value this mill uses daily.
  2. Polyester Knit Basics: The Backbone of Performance — The backbone of performance knits is polyester filament, and the decisive measure is denier per filament: the same 150-denier yarn gives ≈3.1 dpf at 48 filaments and ≈1.0 dpf at 144 — identical weight, two completely different fabrics. Finer filaments mean more surface area and softness; tenacity is measured to ISO 2062.
  3. DTY Textured Yarn: Bulk, Stretch and Wicking — DTY is flat POY filament given a permanent crimp by false-twist in a first heater at ~200–220 °C; a second heater (yarn exit ~130–180 °C) kills residual torque. That crimp is exactly what FDY lacks — bulk, stretch and moisture transport all come from it. Crimp contraction is measured to ISO 5688.
  4. Polyester Blends: Cotton, Elastane, Modal — Pure polyester gives strength, fast drying and colour fastness; in return it brings a cool synthetic hand, static build-up and limited stretch. Blending exists for one reason — to let a second fibre cover that gap: cotton adds hand and moisture pickup, elastane adds recovery, modal adds drape and softness. The cost is pilling tendency and dyeing two fibres separately.
  5. Recycled Polyester (rPET) in Knits — What decides rPET quality is chain length — intrinsic viscosity (ASTM D4603 · ISO 1628-5). PET is hygroscopic: at a melt temperature of ~280 °C, moisture in the chain hydrolytically cleaves the ester bond, so IV drops during recycling. Solid-state polycondensation (~200–220 °C) rebuilds it; GRS/RCS certify chain of custody, not performance.
  6. Naming in Polyester Knits: When One Fabric Has Many Names — In textiles the same fabric carries several names, and this is the most common source of misunderstanding between buyer and mill: süprem = single jersey = polyester jersey, iki iplik = French terry, double-face interlock = ponte. The confusion is not only in names — yarns below 1 dpf count as microfilament, so two fabrics sharing a name can feel entirely different. An order should always be defined by structure + weight + yarn.

Frequently asked questions

Do you export yarn by the container?

Yes. We export polyester yarn by the container. The delivery term (Incoterms) and the payment terms are set in the quotation. State the yarn count, colour, quantity and port of destination in your request.

Can you produce a yarn count that is not in the catalogue?

Denier and filament counts that are not in the catalogue can be produced on request when the quantity is suitable. State the denier and filament count, lustre, colour and quantity in your request.

Do you develop fabrics with non-polyester fibres (modal, cotton)?

Our production is predominantly polyester. Non-polyester fibres and blends are evaluated case by case. Send the target composition and, if you have one, the reference fabric with your request.

Let’s pick the right fabric for your project together.

If the guides didn’t answer your question, talk to our team; we’ll plan weight and composition around your needs.

Get in touch
  • ISO + OEKO-TEX
  • 1 business day is our response time
FERSAN · PERFORMANCE FABRIC Established 1982
Request a sample or quote

On this page

Top