Structure and Weight Guides for Polyester Knits
A polyester knit is defined once its structure, its weight in g/m² and its stretch class are written together. The choice between single and double bed, between a closed face and an open pore, and between a base with or without elastane changes hand, opacity and behaviour. These ten guides explain each structure and its weight band.
This category covers how a polyester knit is built and how that build is written into a specification. The starting point is the needle bed. Single jersey is knitted on one bed, while interlock, rib and ponte are knitted on two. Weight, elastane, open structures such as mesh and piqué, and bodied structures such as fleece and scuba follow. The guides also tie the market names used in buying correspondence to the construction behind them. A market name or a single weight figure does not define a fabric. Two suppliers send comparable samples only when structure, weight band and elastane share are written together.
The ten guides run from foundation to detail. Start with single jersey and interlock, continue with the double-face structures, and then read the GSM guide and the weight map. The elastane guide follows, then the two guides on breathable mesh and piqué, and then fleece and scuba. The teamwear naming map closes the series and applies all of these choices to a single sample request.
Decisions made in this category
| Decision | What to check |
|---|---|
| Should the body be single jersey or interlock? | The number of needle beds, edge curling, whether both faces are identical, and the weight the same yarn gives in each structure Single Jersey vs Interlock: Choosing a Polyester Knit |
| Which double-face structure suits the garment part? | Crosswise recovery for collars and cuffs (rib), a smooth, stable face for the body (interlock), body and upright stance for structured pieces (ponte) Rib, Interlock and Ponte: Choosing the Right Double-Face Knit |
| Which weight does the product need? | The g/m² band for the end use, with hand and opacity confirmed on a real sample, because yarn and structure change the result at the same GSM GSM Weight Guide: Choosing the Right Fabric Weight |
| Does the product need two-way or four-way stretch? | The elastane share and the base it runs in: two-way on single jersey, four-way usually on an interlock base With or Without Elastane? Stretch and Recovery in Polyester Knits |
| How is breathability compared between mesh and piqué? | Pore type and weight read together, with air permeability measured to ISO 9237 Piqué, Bird’s-Eye and Mesh: The Anatomy of Breathable Polyester Knits |
| Is the sample scuba, ponte or neoprene? | The cut edge (a foam core means neoprene), the stretch direction (four-way or two-way) and the face (flat or a faint horizontal rib) Scuba Fabric: How It Differs from Ponte and Neoprene, and the Weight Map |
| How does a teamwear market name become a specification? | Five lines: construction, weight window in g/m², composition and elastane share, expected finish, and whether the ground is prepared for sublimation Teamwear Knit Fabrics: The Names Behind Kappa, Damla, Kaz Ayağı and Polymesh |
Key facts
- Single jersey is knitted on one needle bed, differs face to back and curls at the edges (80–200 g/m²). Interlock is knitted on two beds, is identical on both faces and gives a stable surface that does not curl (80–260 g/m²). Single Jersey vs Interlock: Choosing a Polyester Knit
- Tees typically sit at ~120–180 g/m², sweatshirts and joggers at ~250–350 g/m², and jacket linings and structured outerwear at ~300 g/m² and above. With the same structure and yarn, a higher GSM means more opacity and generally more durability. GSM Weight Guide: Choosing the Right Fabric Weight
- Single jersey and interlock feel very different even at the same 200 g/m², so the bands on a weight map are read as typical ranges, not exact recipes. The Weight Map: Which Knit Goes Where, from 60 to 500 g/m²
- Stretch interlock carries 5–12% elastane and stretches four ways, while stretch single jersey carries 5–8% and stretches two ways. “With elastane” alone therefore does not mean four-way stretch. With or Without Elastane? Stretch and Recovery in Polyester Knits
- Breathable micro mesh runs at 70–130 g/m², sports mesh at 100–170 g/m², bird’s-eye mesh at 120–200 g/m² and piqué at 100–370 g/m². The real claim of these structures is air permeability, measured to ISO 9237. Mesh and Piqué: Breathable Polyester Knits
- In fleece the warmth comes from a raised pile across 100–400 g/m², while in scuba the body comes from the double-faced structure itself. “Fleece” alone is therefore not a specification until structure, weight and surface treatment are written together. Fleece and Scuba: Structured Polyester Knits
- Knitted fabric containing 5% or more elastomeric yarn by weight is declared under 6004.10, and anything below it under 6006.32. In scuba the elastane share therefore sets the customs declaration as well as the hand. Scuba Fabric: How It Differs from Ponte and Neoprene, and the Weight Map
- Within the polymesh family the hole opens from a 70 g/m² lining mesh to a 250 g/m² jacquard mesh. Unless hole size, weight and elastane share are written down, two suppliers’ “polymesh” will not be the same cloth. Teamwear Knit Fabrics: The Names Behind Kappa, Damla, Kaz Ayağı and Polymesh
Reading order
- Single Jersey vs Interlock: Choosing a Polyester Knit — Single jersey is knitted on one needle bed: light, fluid, different on each face and curling at the edges (80–200 g/m²). Interlock is double bed: fuller, identical on both faces, a stable surface that does not curl (80–260 g/m²). Even at the same weight the two feel different, which is why an order is defined by structure + weight + yarn.
- Rib, Interlock and Ponte: Choosing the Right Double-Face Knit — Single jersey is single-faced and its edges curl; three double-faced structures solve that differently. Rib gives high crosswise recovery (150–500 g/m²), interlock builds a stable surface identical on both faces (80–400 g/m²), and ponte puts body into the shape. The choice is made together with the weight band: at the same structure, a different weight means a different hand.
- GSM Weight Guide: Choosing the Right Fabric Weight — GSM (g/m²) is a fabric’s weight per square metre and the fastest indicator of what it is for: tees typically sit at ~120–180 g/m², sweatshirts and joggers at ~250–350 g/m², jacket linings and structured outerwear at ~300 g/m² and above. With the same structure and yarn, higher GSM means more opacity and generally more durability.
- The Weight Map: Which Knit Goes Where, from 60 to 500 g/m² — Weight is the fastest indicator of what a knit is for, and Fersan’s ten families line up on a single axis from 60 to 500 g/m². The light band — mesh and jersey — goes to linings and summer tops; the middle band, piqué and interlock, to polos and dresses; the upper band, French terry, rib and fleece, to sweatshirts, collar-and-cuff trims and outer layers. At the same weight, different structures give different hand: weight alone is not a quality measure.
- With or Without Elastane? Stretch and Recovery in Polyester Knits — Stretch in knits comes in three distinct classes, and confusing them means ordering the wrong fabric: elastane-free structures stretch mechanically only (single jersey 80–200 g/m²), jersey with elastane stretches two-way (120–250 g/m²), elastane interlock four-way (120–300 g/m²). That is why an order should be defined by structure + weight + stretch class.
- Mesh and Piqué: Breathable Polyester Knits — Polyester does not absorb moisture; in mesh and piqué the cooling comes from STRUCTURE, not the fibre. Pore architecture is read together with weight: breathable micro mesh 70–130 g/m², sports mesh 100–170 g/m², bird’s-eye mesh 120–200 g/m², piqué 100–370 g/m². The real claim of the structure is air permeability, measured to ISO 9237.
- Piqué, Bird’s-Eye and Mesh: The Anatomy of Breathable Polyester Knits — Because polyester does not absorb moisture, the cooling comes from structure: knit-tuck cells and deliberate holes open air channels in the fabric. Within one family the weight band is wide — mesh 70–250 g/m², piqué 100–370 g/m² — and breathability cannot be compared without reading pore and weight together. Air permeability is measured to ISO 9237.
- Fleece and Scuba: Structured Polyester Knits — Fleece and scuba are the two structured families where polyester is used for warmth and body, and the difference is at the surface: in fleece the warmth comes from a raised pile (100–400 g/m²), in scuba the body comes from the double-faced structure itself. Because the weight band is wide, “fleece” alone is not a specification — structure + weight + surface treatment must be written together.
- Scuba Fabric: How It Differs from Ponte and Neoprene, and the Weight Map — Scuba is an elastane double-face knit made on a double bed: flat-faced, lightly springy, four-way stretch. It is not neoprene — there is no foam inside it. It is not ponte either: ponte stretches two ways and carries a faint rib, scuba stretches four ways and reads flat. This guide separates the three and maps the 200–400 g/m² band garment by garment.
- Teamwear Knit Fabrics: The Names Behind Kappa, Damla, Kaz Ayağı and Polymesh — Teamwear fabric is a use category, not a construction: every knitted polyester face that goes into sports or corporate kit is filed under it. The Turkish market names those faces kappa, damla, kaz ayağı and polymesh — names that describe the look, not the knit. This guide ties each market name to what the machine actually does, and maps the weight band garment part by garment part.
Frequently asked questions
Is there a training fabric with a scuba-like hand that still breathes?
Scuba imitates the firm stance of neoprene, but it breathes because it has no foam core. If higher air permeability is needed, mesh and piqué structures with deliberate air gaps at the surface are chosen. Air permeability is measured to ISO 9237.
What weight of stretch single jersey suits a performance polo or tee?
Lightweight performance and everyday tees typically sit at ~120–180 g/m², and the upper end (160–180) gives a fuller-bodied, more opaque hand. Jersey with elastane stretches two-way and typically runs at 120–250 g/m².